Engineering & Mechanics
Statics, structures, machine elements, fluid power and manufacturing calculations.
Statics & Equilibrium
Forces, moments and planar equilibrium.
Torque
Calculate torque from force, lever arm length and the angle between them.
τ = F × r × sin(θ)Force Components 2D
Resolve a planar force into signed Cartesian components. Angle is measured counterclockwise from positive X.
Fx = F cos(θ); Fy = F sin(θ)Resultant Force 2D
Sum corresponding signed horizontal and vertical force components and report the resultant direction from +X.
Rx = ΣFx; Ry = ΣFy; R = √(Rx² + Ry²); θ = atan2(Ry, Rx)2D Equilibrium Balance
Find the force and moment that would balance the supplied signed sums. Positive X/Y and counterclockwise moment are positive.
Fbal,x = −ΣFx; Fbal,y = −ΣFy; Mbal = −ΣMStress & Strain
Axial loading, material strain and thermal response.
Normal Stress
Calculate average axial normal stress over a uniform cross-sectional area.
σ = F/AAverage Shear Stress
Calculate average shear stress assuming the load is shared equally across the stated shear planes.
τavg = F/(nA)Axial Strain
Calculate signed engineering strain from a length change and original gauge length.
ε = ΔL/L; ε% = 100ε; με = 10⁶εAxial Deformation
Estimate an axially loaded straight, homogeneous member using linear elasticity and a centered load.
ΔL = FL/(AE); σ = F/A; ε = σ/EThermal Expansion & Stress
Estimate free thermal movement or the stress and reaction in a fully restrained uniform member.
ΔLfree = αLΔT; σrestraint = −EαΔT; F = σAMaterial & Section Properties
Cross-section geometry, inertia, mass and weight.
Cross-Section Properties
Calculate area, centroidal area moments and elastic section moduli for common symmetric sections.
Rectangle: A=bh, Ix=bh³/12, Iy=hb³/12; circle: I=πd⁴/64; Z=I/cPolar Area Moment — Circular Sections
Calculate the polar second moment of area for a solid or concentric hollow circular section.
Solid: J=πd⁴/32; hollow: J=π(Do⁴−Di⁴)/32Radius of Gyration
Calculate the area radius of gyration from a second moment of area and cross-sectional area.
r = √(I/A)Mass from Density & Volume
Calculate mass and weight from user-supplied density and volume using standard gravity.
m = ρV; W = mg; g₀ = 9.80665 m/s²Beam Analysis & Deflection
Ideal beam reactions, shear, moment and deflection.
Simply Supported Beam — Point Load
Analyze one point load on a simply supported Euler–Bernoulli beam with small deflection and linear elasticity.
RA=P(L−a)/L; RB=Pa/L; Mmax=Pa(L−a)/LSimply Supported Beam — Uniform Load
Analyze a full-span uniform load on a simply supported Euler–Bernoulli beam with small deflection and linear elasticity.
RA=RB=wL/2; Mmax=wL²/8; Vmax=wL/2; δmax=5wL⁴/(384EI)Cantilever Beam — End Point Load
Analyze a downward point load at the free end of a linear elastic Euler–Bernoulli cantilever with small deflection.
Mmax=PL; Vmax=P; δmax=PL³/(3EI)Cantilever Beam — Uniform Load
Analyze a full-length uniform load on a linear elastic Euler–Bernoulli cantilever with small deflection.
Mmax=wL²/2; Vmax=wL; δmax=wL⁴/(8EI)Torsion & Shafts
Rotating shaft power, torsional stress and twist.
Shaft Power & Torque
Calculate angular speed and shaft torque from transmitted power and rotational speed.
ω = 2πn/60; T = P/ωTorsional Shear Stress
Estimate maximum elastic shear stress in a circular shaft using the polar area moment.
τmax = Tc/J; J = π(Do⁴−Di⁴)/32Shaft Angle of Twist
Calculate twist of a straight, uniform circular shaft under constant torque.
φ = TL/(JG)Required Solid Shaft Diameter
Estimate the theoretical minimum solid shaft diameter from an explicitly supplied allowable shear stress.
d = ∛(16T/(πτallow))Columns & Buckling
Ideal Euler column stability and slenderness.
Euler Critical Buckling Load
Calculate ideal elastic Euler buckling load for a slender, straight column with the entered effective-length factor.
Pcr = π²EI/(KL)²; σcr = Pcr/AColumn Slenderness
Calculate effective length and slenderness ratio from length, end-condition factor and radius of gyration.
Le = KL; λ = Le/rBuckling Safety Factor
Compare applied compressive load with either a supplied critical load or the ideal Euler critical load.
n = Pcr/P; Euler option: Pcr = π²EI/(KL)²Springs
Linear spring rates, loads, energy and combinations.
Helical Compression Spring Rate
Estimate the rate of an ideal close-coiled helical spring with circular wire.
k = Gd⁴/(8D³n)Spring Force & Deflection
Calculate force for a linear spring at a stated deflection using Hooke’s law.
F = kxSpring Energy
Calculate elastic energy stored by an ideal linear spring at a stated deflection.
E = ½kx²; F = kxSprings in Series & Parallel
Calculate equivalent rate for independent linear springs arranged in series or parallel.
Series: 1/keq=Σ(1/ki); parallel: keq=ΣkiGears & Drives
Ideal gear geometry, speed, power and drive ratios.
Gear Ratio & Output Speed
Calculate ideal speed ratio for a meshing gear pair from tooth counts.
i = z2/z1; n2 = n1z1/z2Spur Gear Geometry
Calculate pitch diameters and center distance for a pair of ideal standard spur gears.
d1=mz1; d2=mz2; a=(d1+d2)/2Gear Torque & Power
Calculate input and output power and output torque from measured input torque, speeds and an explicit efficiency.
Pin=Tinωin; Pout=ηPin; Tout=Pout/ωoutBelt & Chain Drive
Estimate output speed for an ideal belt or chain drive with no slip.
Belt: n2=n1D1/D2; chain: n2=n1z1/z2Transmission Efficiency
Calculate efficiency and power loss from input and output power for a passive transmission.
η = Pout/Pin × 100%; Ploss = Pin − PoutBearings & Lubrication
Bearing equivalent loads and basic rating life.
Bearing L10 Life
Estimate basic rating life using the bearing type exponent and user-supplied dynamic rating and equivalent load.
Ball: L10=(C/P)³; roller: L10=(C/P)^(10/3); L10h=L10·10⁶/(60n)Equivalent Dynamic Bearing Load
Calculate equivalent dynamic load using explicitly supplied radial/axial factors; no bearing lookup table is assumed.
P = XFr + YFaStatic Bearing Safety
Calculate the ratio of static load rating to equivalent static load without prescribing a pass/fail threshold.
s0 = C0/P0Fasteners & Joints
Simplified bolt, weld and tightening estimates.
Bolt Tensile Stress
Calculate average tensile stress from axial bolt load and supplied thread tensile-stress area.
σ = F/AtBolt Shear Stress
Estimate average bolt shear stress with equal load sharing across the entered bolt count and shear planes.
τ = F/(n m πd²/4)Bolt Preload & Tightening Torque
Estimate bolt preload from tightening torque using the explicitly entered nut factor and nominal diameter.
F = T/(Kd)Weld Throat Stress
Estimate average static stress over the effective throat area of a uniformly loaded fillet weld.
τ = F/(0.707aL)Hydraulics & Pneumatics
Cylinder forces, motion and ideal pump power.
Hydraulic Cylinder Force
Calculate ideal extension and retraction forces for a single-rod hydraulic cylinder.
Aext=πD²/4; Aret=π(D²−d²)/4; F=pACylinder Speed & Flow
Estimate piston speed and time for a constant-flow, constant-area cylinder stroke.
v = Q/A; t = L/vHydraulic Pump Power
Calculate ideal hydraulic output power and required input power from pressure, flow and efficiency.
Phyd = pQ; Pin = Phyd/ηPneumatic Cylinder Force
Calculate ideal extension and retraction force using gauge pressure and piston/rod geometry.
Fext=pgπD²/4; Fret=pgπ(D²−d²)/4Machining & Manufacturing
Cutting speed, feeds, material removal and power.
Cutting Speed & Spindle RPM
Convert between cutting speed and spindle speed for a stated tool or workpiece diameter.
n = 1000Vc/(πD); Vc = πDn/1000Machining Feed Rate
Calculate linear feed rate for turning/drilling or milling from the corresponding feed convention.
Turning/drilling: Vf=f n; milling: Vf=fz z nTurning Material Removal Rate
Estimate turning material removal rate from diameter, spindle speed, feed and depth of cut.
MRR = πD n f apMachining Time
Estimate single-pass travel time from machining length and linear feed rate.
t = L/VfCutting Power Estimate
Estimate cutting power from explicitly supplied specific cutting force and material removal rate.
Pc(kW) = kc·MRR/60,000,000