Electrical & Electronics
Circuits, power and component analysis.
Electrical Fundamentals
Core electrical quantities, material properties and Ohm’s law.
Ohm’s Law
Solve a DC Ohm’s law quantity or electrical power using the selected independent formula. Ideal resistor model.
V = IR; P = VI = I²R = V²/RElectric Charge, Current & Time
Solve charge, current or elapsed time using Q = It.
Q = It; I = Q/t; t = Q/IConductor Resistance & Resistivity
Solve one variable in R = ρL/A. Resistivity is supplied at the stated material temperature; no automatic temperature correction or material preset is assumed.
R = ρL/A; ρ = RA/L; L = RA/ρ; A = ρL/RConductance & Conductivity
Convert between resistance and conductance, or between resistivity and conductivity. These are distinct lumped and material properties.
G = 1/R; σ = 1/ρCurrent Density
Solve current density, current or conductor cross-sectional area using J = I/A. Area is represented in square metres.
J = I/A; I = JA; A = I/JDC Circuits
Direct-current network rules, branches and circuit analysis.
Kirchhoff’s Current Law
Solve one entering or leaving node current, or check a fully specified node balance. Positive values are magnitudes in the explicitly named direction.
ΣIin = ΣIoutKirchhoff’s Voltage Law
Sum signed loop voltages in the stated traversal direction. Sources traversed as rises are positive; drops are negative.
ΣVloop = 0Series DC Circuit
Analyze a series string of positive resistors connected to an ideal DC voltage source.
Rtotal = ΣRi; I = Vs/Rtotal; Vᵢ = IRᵢ; Pᵢ = I²RᵢParallel DC Circuit
Analyze positive resistor branches across an ideal DC voltage source. A zero-ohm branch is an ideal short and makes source current unbounded in this ideal model.
1/Req = Σ(1/Ri); Ii = Vs/Ri; Itotal = ΣIiSimple Mixed DC Circuit
Analyze the explicitly defined topology: R1 in series with a parallel network of R2 and R3. No arbitrary circuit topology is implied.
Req = R1 + (R2 || R3); I = Vs/ReqAC Circuits
Sinusoidal steady-state waveforms, reactance and resonance.
AC Waveform
Calculate sinusoidal waveform quantities. Enter the amplitude as peak or RMS; frequency, period and angular frequency are related exactly by the selected mode.
v(t) = Vpeak sin(ωt + φ); Vrms = Vpeak/√2; T = 1/f; ω = 2πfCapacitive Reactance
Solve one variable in ideal sinusoidal capacitive reactance Xc = 1/(2πfC).
Xc = 1/(2πfC)Inductive Reactance
Solve one variable in ideal sinusoidal inductive reactance XL = 2πfL.
XL = 2πfLSeries RLC Circuit
Steady-state sinusoidal series RLC model using RMS supply and component voltages. Ideal components and a single frequency are assumed.
Z = √(R² + (XL − XC)²); φ = atan((XL − XC)/R); I = Vrms/ZIdeal LC Resonant Frequency
Solve the ideal lossless LC resonance relationship. Real component losses and parasitics are not included.
f0 = 1/(2π√(LC))Resistors & Networks
Equivalent resistance, dividers and resistor identification.
Series & Parallel Resistor Networks
Calculate equivalent resistance for two or more positive resistor values. Add or remove individual resistor entries (up to 32).
Series: Req = ΣRi; parallel: 1/Req = Σ(1/Ri)Voltage Divider
Calculate an unloaded two-resistor divider or include an explicit parallel load on R2.
Vout = Vin·Rlower/(R1 + Rlower); Rlower = R2 || RL when loadedCurrent Divider
Split a total current among two or more positive parallel resistances using conductance ratios.
Ii = Itotal·(1/Ri)/Σ(1/Rj)Resistor Color Code
Decode valid 4-band, 5-band or 6-band resistor markings from embedded reference tables. Band order is significant digits, multiplier, tolerance, then temperature coefficient.
R = significant digits × multiplier; limits = R(1 ± tolerance)Capacitors & Inductors
Ideal component networks, stored energy and first-order transients.
Capacitor Charge & Voltage
Solve charge, capacitance or voltage for an ideal capacitor using Q = CV.
Q = CV; C = Q/V; V = Q/CCapacitor Networks
Calculate ideal equivalent capacitance for two or more capacitors.
Parallel: Ctotal = ΣCi; series: 1/Ctotal = Σ(1/Ci)Inductor Networks
Calculate ideal series or parallel equivalent inductance. Mutual magnetic coupling is ignored.
Uncoupled series: Ltotal = ΣLi; parallel: 1/Ltotal = Σ(1/Li)Stored Electrical Energy
Solve stored energy or one component quantity for an ideal capacitor or inductor.
Capacitor: E = ½CV²; inductor: E = ½LI²RC Time Constant & Transient
Calculate an ideal first-order RC charging or discharging response and plot voltage versus time.
τ = RC; charge: Vc = Vs(1 − e^(−t/τ)); discharge: Vc = V0e^(−t/τ)RL Time Constant & Transient
Calculate an ideal first-order RL step or current decay and plot current versus time. Switching transients, winding resistance beyond entered R and saturation are omitted.
τ = L/R; step: i = (V/R)(1 − e^(−t/τ)); decay: i = I0e^(−t/τ)Diodes & Transistors
Explicit simplified device models for practical circuit estimates.
LED Series Resistor
Calculate the ideal current-limiting resistor and its power. Optional E12/E24 suggestions are shown separately and the calculated value is never silently replaced.
R = (Vs − Vf)/I; PR = I²RDiode Operating Point (Simplified)
Estimate a series diode-resistor operating point using an explicit ideal, constant-drop or user-defined forward-voltage model. Reverse breakdown is not modeled.
I = max((Vs − Vf)/R, 0) under the selected forward modelZener Shunt Regulator
Analyze a basic shunt Zener regulator with explicit supply, Zener voltage, series/load resistances and device ratings.
IR = (Vs − Vz)/Rs; IL = Vz/RL; Iz = IR − ILBJT Base Bias & Switching Estimate
Estimate a base-driven NPN stage using explicit VBE, beta or forced beta, collector load and supply. This is not a transistor simulation.
IB = max((Vin − VBE)/RB, 0); IC ≈ βIB, limited by collector loadMOSFET Low-Side Switch Loss
Estimate low-side conduction drop and loss from load current and RDS(on) specified at the actual gate-drive condition. Switching losses and detailed thermal behavior are excluded.
Vdrop = IRDS(on); Pcond = I²RDS(on)Digital Electronics
Logic gates and safe Boolean expression evaluation.
Logic Gate Calculator
Evaluate one binary logic gate and show its complete truth table. Inputs accept only 0 or 1.
Boolean output determined by selected gate truth tableBoolean Truth Table Generator
Generate a full truth table for expressions using A–D, parentheses, prefix !/NOT, AND (&), XOR (^), OR (|), with precedence NOT > AND > XOR > OR. Up to four variables. No JavaScript evaluation is used.
Parse Boolean expression → enumerate all input combinations → evaluate safelyPower & Energy
Electrical power, consumption, efficiency and correction.
Single-Phase AC Power
Calculate single-phase apparent, active and reactive power from RMS voltage/current, power factor and explicit inductive/capacitive sign.
S = VrmsIrms; P = S·PF; Q = ±S√(1 − PF²); φ = ±acos(PF)Balanced Three-Phase Power
Calculate power for a balanced three-phase system using line-to-line RMS voltage and line RMS current.
S = √3 VLIL; P = √3 VLIL·PF; Q = ±√3 VLIL√(1 − PF²)Energy Consumption & Electricity Cost
Estimate energy and cost for one or more devices. Enter comma separated power values in W and matching daily operating hours; price and fee are explicit user inputs. Period presets use 1, 30 or 365 days.
E(kWh) = Σ[Pi(W)·hi(h/day)·days]/1000; cost = E·price + feesElectrical Efficiency
Calculate output/input power efficiency. Physical mode rejects output above input; measured comparison mode reports an apparent value above 100% with a warning.
η = Pout/Pin × 100%Single-Phase Power Factor Correction
Estimate an ideal shunt capacitor for single-phase correction from initial and target power factor. The three-phase formula is not applied.
Qc = P(tanφ1 − tanφ2); C = Qc/(2πfV²)Electromagnetic Applications
Ideal transformer, motor and solenoid engineering estimates.
Ideal Transformer
Solve an ideal transformer ratio using explicitly identified primary and secondary quantities. Core/copper losses, magnetizing current and saturation are excluded.
Vs/Vp = Ns/Np; Ip/Is = Ns/Np; VpIp = VsIsTransformer Efficiency & Losses
Calculate efficiency and losses from measured input/output power, or from explicit output power plus copper and core loss estimates.
η = Pout/Pin × 100%; Ploss = Pin − PoutDC Motor Power & Speed
Estimate an ideal power balance from measured electrical input and mechanical torque/speed. No motor electromagnetic design model is implied.
Pin = VI; Pmech = Tω; ω = 2πn/60; η = Pmech/PinThree-Phase Induction Motor Speed & Slip
Calculate synchronous speed, signed slip and rotor frequency for a balanced induction motor. Standard motoring operation has rotor speed from zero to synchronous speed.
Ns = 120f/P; s = (Ns − Nr)/Ns; fr = sfLong Solenoid Magnetic Field
Estimate the internal field of an ideal long solenoid. Choose an explicit air-core model or supply core relative permeability; fringing and saturation are ignored.
B = μ0 μr NI/l